Thank you for
purchasing the GPS vehicle tracker. This manual shows how to operate the device smoothly and correctly. Make sure to
read this manual carefully before using this product. Please note that specification and information are subject to
changes without prior notice in this manual. Any change will be integrated in the latest release. The manufacturer
assumes no responsibility for any errors or omissions in this document.
Working Based on existing GSM/GPRS
network and GPS satellites, this product can locate and monitor any remote targets by SMS or GPRS.
1.1
Positioning and Tracking: Through the on-line Positioning Platform or the
cell phone to locates at times, and get the working status. You can choose the Positioning Platform by yourself. 1.2 Triggering Emergency Alarm:
When there is a emergency happened on the vehicle, you can put on the button and the installed unit will send out alarm
to the authorized numbers.
1.3 Remote controlling oil and circuit: you can control the oil and circuit via the unit by SMS
in anywhere and anytime.
1.4
Remote Monitoring: In anywhere and anytime, call the phone number in the
unit, when it connects, you can monitor the sound around 5 meter. 1.5 Movement Alert: Send SMS to
the unit to start the movement alert function. When the vehicle is moving, the unit will send the movement alert to all
authorized numbers.
1.6 Overspeed Alert: Send SMS to the unit to start the movement alert function. When the vehicle
is overspeed, the unit will send the overspeed alert to all authorized numbers.
1.7 Geo-fence: Set up a geo-fence for the unit to restrict its movements within a district. The
unit will send the message to all authorized numbers when it breaches the district.
1.8 the unit: send SMS to resume the default of unit.
1.9 Auto Track: You can set up auto track by SMS or on-line positioning platform.
1.10 Mileage statistics; ACC checking; cutting off power and alarm.
1.11 Compatible with the original anti-theft alarm: It will send SMS alarm after the original
anti-theft alarm warning.
1.12 Modify the IP and Port of Communication Protocol for different on-line positioning platform
2 Applications
lVehicle rental / Fleet management etc
lProtect wealth etc
lProvide peace-of-mind for businessmen
lManage personnel
3 Hardware Description
3.1 Front face 3.2 Rear face
3.3 Side face
3.4 Bottom face
4 Specs.
Content
Specs.
Dim.
85mmx 63mmx 25mm(3.3”*2.5”*0.98”)
Weight
160g
Network
GSM/GPRS/GPS
Band
850/1800/1900Mhz or 900/1800/1900Mhz or 850/900/1800/1900
GPS chip
SIRF3 chip
GSM/GPRS module
Siemens MC55 or
Siemens MC56 or Simcom300 or Simcom340
GPS sensitivity
-159dBm
GPS accuracy
5m
Time To First Fix
Cold status 45s
Warm status 35s
Hot status 1s
Work voltage
10V—36V
Battery
Chargeable changeable
3.7V 1500mAh Li-ion battery
Standby
48hours
Storage Temp.
-40°C to +85°C
Operation Temp.
-20°C to +55°C
Humidity
5%--95% non-condensing
5 Usage
5.1 SIM card installation
Make sure that there is no call
transfer and call display is on, and PIN code off. The SMS message must in Text format, can’t be
identified for PDU format.
5.1.1 Put SIM card into card box.
5.1.2 Put the card box into host as
picture.
.
5.2
GPS Vehicle Tracker Installation
GPS/GSM/GPRS tracker should be installed by technical professional
of local service centre. Without
permission, the user can’t repair and move the tracker randomly.
If users do, any unfortunate damage should be compensated by himself.
5.2.1
Install Wire Box
5.2.2 GPS
Vehicle Tracker Installation
Installation steps (caution: the following installation should under no power, otherwise will
be dangerous)
Wire for cutting off circuit of the tracker
White wire connects relay feet 86; 85 feet to 12 VDC anode, 87 feet and 30 feet are in series in the supply power
circuits.
Wire for cutting off
oil of the tracker
Yellow wire connects the relay feet 86;85 feet to 12 VDC anode, 87 feet and 30 feet in series in the supply oil circuits.
Emergency triggering alarm
The blue wire connects the anode of the alarm button, and
the black wire connects the cathode of the alarm button.
Power supply line
The red wire connects 12V“+”;Black wire connects to12V“-”
.3 Startup
5.3.1 Installed the tracker in the car,then put the SIM card into the tracker host
outdoors.
5.3.2 For first use, please initialize the unit and restore it to default setting.( please
refer to 5.4for instruction.)
5.3.3 or 40 seconds, the unit will begin to work and acquire the GSM signals as well as the
GPS signals, and the red indicator will keep flashing every 2 seconds when the GPS module is in standby mode. When the
blue indicator is keep shine, the unit has been located.
5.3.4 When this unit receives GPS signals normally, you can use it and do all the following
settings.
5.4 Initialization
Send “begin+password” in SMS to
the unit, it will reply “begin ok” and initialize all the settings. (Default password: 123456)
5.5 Change the password
5.5.1 Send SMS "password+old password+space+new" password to change the password.
Remark: Make sure the new password is in
6 digits, or else the tracker can not recognize the password.
5.5.2 you can Send "resume+password" to the tracker, to restore the original setting
in case of losing the new password.
5.6 Authorization
There are only 4 numbers able to be authorized.
5.6.1
Call the tracker for 10 times, it will make the cell phone number as the authorized number automatically.
5.6.2 Send SMS "admin+password+space+cell phone number" to set up a
authorized number. The other authorized numbers should be set by the first authorized number. If the number is
successfully authorized, the unit will reply "admin ok!" in SMS.
5.6.3
Send SMS "noadmin+password+space+authorized number" to delete the authorized number.
5.6.4
For roaming purpose, you have to add your country code ahead of the cell phone number, for example, please "send
admin123456 008613311113333" to tracker to set 13311113333 as an authorized number.
5.7 Real-time polling
5.7.1
If there is no authorized number, when any number dials up the unit, it will report a Geo-info; If there is already an
authorized number, then it will not respond when an unauthorized number calls it up.
5.7.2
When an authorized number dials up the unit, it will hang up and report a real-time Geo-info as below:
5.8 Auto Track
Report a Geo-info at 30s intervals to
the authorized numbers for 15 times:
5.8.1 Set up: Send SMS "at30sum15+password" to the unit, it will report the Geo-info at 30s
intervals for 15 times. The setting must be maximum 65535 in value.
5.8.2 Send SMS "at30sum0" to the unit, it will reply SMS heaps of times.
5.8.3 Cancel: Send noat+password to delete the “auto track”.
5.9 Remote control oil and circuit
5.9.1 Control oil
Send SMS "stopoil+password" to
control oil. For example send SMS:stopoil123456
To supply the oil again, send SMS "supplyoil+password" to the unit.
5.9.2 Control circuit
Send SMS "stopelec+password" to control circuit. For example send SMS:stopelec123456
To supply the circuit again, send SMS "supplyelec+password" to the unit.
If there is no authorized number, all
number can control. If there is already an authorized number, only the authorized number can control.
5.10 Modes switch between "tracker"
and "monitor"
5.10.1 The default mode is "tracker".
5.10.2 Send SMS "monitor+password" to the unit, and it will reply “monitor ok!” and
switch to “monitor”mode.
5.10.3 Send SMS "tracker+password" to the unit, it will reply “tracker ok!” and restore
to “track” mode.
5.11 Geo-fence
Set up a geo-fence for the unit to
restrict its movements within a district. The unit will send the message to the authorized numbers when it breaches the
district.
5.11.1 Set up: When the unit stays immobile in a place for 3-10 minutes, the user can Send SMS
"stockade+password+space+longitude,latitude;longitude,latitude" to unit to set the restricted district. In case of
breach, it will send SMS “stockade!+geo-info” to the authorized numbers.
Remark : The first longitude& latitude
is coordinate of the top left corner of the Geo-fence, while the second longitude&latitude is the coordinate of the
bottom right corner. It will alarm one time in each setting.
5.11.2 Cancel: Send SMS "nostockade+password" to deactivate this function.
This function will be out of effect
after the unit moves outside the district.
5.12 Movement alert
5.12.1 Set up: When the unit stays immobile in a place for 3-10 minutes, the user can send SMS
"move+password" to the unit, then the unit will reply “move ok!”. In case of such a movement, it will send SMS
“Move” along with a Geo-info to the authorized numbers. It will alarm one time in each setting.
5.12.2 Cancel: Send SMS "nomove+password" to deactivate the movement alert.
Remark: This function will be out of
effect after the unit moves outside the district.
5.13 Overspeed alert:
5.13.1 Set up: Send SMS "speed+password+space+080" to the unit (suppose the speed is
80km/h), and it will reply "speed ok!". When the target moves exceeding 80 km/h, the unit will send SMS
"speed+080!+Geo-info" to the authorized numbers. It will alarm one time in each setting.
5.13.2 Cancel: Send SMS nospeed+password to deactivate the overspeed alert
5.14 Restart the tracker.
Send SMS "root+password" to the
tracker. For example“root123456”.The tracker will be restarted.
5.15 SOS button
Press the SOS for 3 second, it will send
"help me !+ Geo-info" to all the authorized numbers every 3 minutes. It will stop sending such a SMS when any
authorized number reply SMS "help me !+ Geo-info" to the tracker.
5.16 Cut power alert
If cut power,the unit will send SMS
alert.
SMS format: " Cut power Alert+Geo-info".
5.17 set number in a online
positioning platform
Add the number on the online positioning
platform for tracking. Adding to the special platform, send SMS "number+trackernumber" to the tracker.
for example “number13500001111”. need
the platform have the fuction.
5.18Modes switch between “telephone” and “web”
5.18.1 For sending GPS data to IP address:
Set up: Send SMS "web + password"
to device.
if set successfully, the device will
reply SMS "set web ok".
After this, you can call the tracker.
The tracker will hang up the phone and report the GPS data to IP address.
5.18.2 For sending GPS data to telephone:
Set up: Send SMS "telephone +
password" to device.
if set successfully, the device will
reply ‘set telephone ok’.
And then, the device will send GPS data
to your telephone by SMS.
Remark:The default is sending the GPS
data to the telephone.
5.19GPRS setting
In order to use GPRS function, the user
needs to set IP, Port and APN ( access point name ) by sending SMS commands.
5.19.1 Set an IP address and port:
The IP address and port of
Communication Protocol in the tracker can be modified and transferred data to other platform. Send SMS "IP
address+port number" to the unit. If the tracker’s IP address and port should be modified to 123.98.43.254and 2456,
send SMS "ip 123.98.43.254port2456"to the tracker.
5.19.2 Set APN
In order to send GPS data to IP address,
you still must set mobile network Access Point Name (APN). If you don’t know the APN, you can consult local network
service supplier. The format of set APN is "apn + password +space + APN". For example you send SMS "apn123456
cmnet" to the device. The device will reply SMS "Set APN ok. " .
5.19.3 If setup successful, the tracker will reply SMS adminip ok
5.19.4 Cancel: Send SMS "noadminip+123456"
6 Cautions
6.1 Make sure to read this manual carefully before using this product.
6.2 Please insert the SIM card before installing, and make sure the SIM card has no password,
otherwise the tracker will not work normally.
6.3 The tracker’s work voltage is
10V-36V. Please use the tracker in the scope of work voltage.
6.4 Please make sure that all the cables of the tracker has been connected rightly, and
then connect the tracker to host power.
6.5 The tracker works in wireless communications, to avoid electromagnetic interference or
incompatible configuration, please stop using your tracker in the noticed place.
6.6 Keep the unit dries. Any liquid, i.e. rain, moisture, may destroy or damage the inside
circuitry.
6.7
Clear the unit with a piece of dry cloth. Don’t clean in chemicals or
detergent.
7. Faults & The solutions
Faults
Solution
Startup Fail
Check the battery and see if it is fully charged or correctly installed.
Hang up Fail
In existence of an authorized number, an unauthorized number dials up the unit.
Please initialize the unit and re-set up the authorized numbers.
Monitor Fail
Check if the authorized number is setup or in the coverage of signals.
Location report in
digits of zeros.
Don’t use it in the place beyond reach of signals. Place the unit outdoors,
especially when starting it up.
